Harley-Davidson CVO PRO STREET BREAKOUT Lifts, Stands & Tie-Downs

Manley

Manley, valve spring kit. Titanium. Std to .650" lift

Arlen Ness

LIFTER BLOCK TITANIUM

Arlen Ness

LIFTER BLOCK BLACK

Drag Specialties

COVER LIFTER C TC 99-17

Feuling

LIFTERS RS OVERSIZED OD 0.843-

Feuling

PINS LIFTER ANTI-ROT O/S

Feuling

Race Series® Chain Drive Camshaft Kit<br><ul><li>Kit includes Reaper® camshaft, Racer Series full travel hydraulic lifters with 0.200" total travel, gasket/o-ring kit that allows installation of Feuling heavy-duty HP+ 0.0165" wall one-piece pushrods or factory one-piece pushrods, ARP® cam/crank fasteners and cam instal kit</li><li>Made in the USA</li><li>Due to the unstable nature of 4-valve engine design with one rocker arm activating two valve springs, Feuling recommends running one-piece pushrods over quick-install adjustable pushrods to maintain maximum cam/valve lift and reduce valvetrain harmonics and associated hydraulic lifter issues. </li><li>Feuling fastener kit is recommended to help prevent cylinder head cracking; kit replaces the rocker shaft bolts with studs and nuts to help reduce the stress of the rocker shaft standoffs.</li><li>Race Series lifters have a slower bleed down rate to handle steep ramped cam and heavy valvesprings, designed to increase engine RPM before valve float.</li><li>Not for '23-'24 models with 121" VVT motors.</li></ul><br>Not for VVT engine. Requires high lift valvesprings. RPM Range: 2250-5900. Overlap: 38.

Feuling

LIFTERS RCE SOLID 99-17TC

Feuling

Race Series® Full-Travel Hydraulic Lifters<br><ul><li>Full-travel hydraulic lifters made from machined steel designed with .200" of travel</li><li>Exceed the needs of large-lift camshafts and higher spring pressures with a slower bleed-down rate</li><li>Maintain proper and critical oil flow to valves, springs, rockers, shafts and valve guides</li><li>Increases engine RPM and valvetrain stability; decreases valve float for maximum valve lift</li><li>Recommended for both strip and performance street engines</li><li>Made in the USA</li><li>High-volume oil pump recommended.</li><li>Recommended for engines running higher than 185 lb (84 kg) valve spring seat pressure.</li></ul><br>Oversize 0.0015" outer diameter.

Feuling

Race Series® Full-Travel Hydraulic Lifters<br><ul><li>Full-travel hydraulic lifters made from machined steel designed with .200" of travel</li><li>Exceed the needs of large-lift camshafts and higher spring pressures with a slower bleed-down rate</li><li>Maintain proper and critical oil flow to valves, springs, rockers, shafts and valve guides</li><li>Increases engine RPM and valvetrain stability; decreases valve float for maximum valve lift</li><li>Recommended for both strip and performance street engines</li><li>Made in the USA</li><li>High-volume oil pump recommended.</li><li>Recommended for engines running higher than 185 lb (84 kg) valve spring seat pressure.</li></ul>

Feuling

Race Series® Short-Travel Hydraulic Lifters<br><ul><li>New revolutionary design with 0.115" of total travel vs. a full travel lifter with 0.200"</li><li>Increases RPM by decreasing valve float and valve-train harmonics while maintaining a quiet engine</li><li>Travel reduction reduces the amount of oil that is required to fill the inside of the lifter which reduces oil aeration inside the lifter on steep, fast action high lift camshaft lobes</li><li>When oil aeration is present inside the lifter, the pushrod seat drops when the lifter rolls onto the front cam lobe ramp after squeezing the aeration down thus creating a noisy poor performing lifter</li><li>Short travel lifters should be set with 0.065" - 0.070" of pre-load and with the normal engine growth from heat will put the operating lifter pre load at or around half travel</li><li>Machined from a steel body and designed to exceed the needs of large lift camshafts and higher valve spring pressures with a slower bleed down rate</li><li>Compatible with either Feuling® HP+® or Race Series® oil pumps and are designed for use with both street and strip engines</li><li>Maintain proper oil flow to the top end, increase engine RPM, valve-train stability, decreasing valve float promoting maximum valve lift</li><li>Precision ground needle roller bearing with high chromium steel axle for long life and minimal friction</li><li>High-flow disc-style quick-reacting check valve for better reaction at higher RPM</li><li>Spin-Tron dyno developed and track proven</li><li>Made in the U.S.A.</li><li>Feuling® recommends pumping up each lifter by hand prior to installation, to remove all air and provide a fully pumped up lifter. Use of a thin weight oil like ATF in a squirt can works well.</li><li>Feuling® recommends Race Series® lifters for engines running higher than 185 lb (84 kg) valve spring seat pressure.</li><li>Feuling® recommends the use of a high volume oil pump which will result in quieter, better performing lifters.</li></ul>

Feuling

Race Series® Short-Travel Hydraulic Lifters<br><ul><li>New revolutionary design with 0.115" of total travel vs. a full travel lifter with 0.200"</li><li>Increases RPM by decreasing valve float and valve-train harmonics while maintaining a quiet engine</li><li>Travel reduction reduces the amount of oil that is required to fill the inside of the lifter which reduces oil aeration inside the lifter on steep, fast action high lift camshaft lobes</li><li>When oil aeration is present inside the lifter, the pushrod seat drops when the lifter rolls onto the front cam lobe ramp after squeezing the aeration down thus creating a noisy poor performing lifter</li><li>Short travel lifters should be set with 0.065" - 0.070" of pre-load and with the normal engine growth from heat will put the operating lifter pre load at or around half travel</li><li>Machined from a steel body and designed to exceed the needs of large lift camshafts and higher valve spring pressures with a slower bleed down rate</li><li>Compatible with either Feuling® HP+® or Race Series® oil pumps and are designed for use with both street and strip engines</li><li>Maintain proper oil flow to the top end, increase engine RPM, valve-train stability, decreasing valve float promoting maximum valve lift</li><li>Precision ground needle roller bearing with high chromium steel axle for long life and minimal friction</li><li>High-flow disc-style quick-reacting check valve for better reaction at higher RPM</li><li>Spin-Tron dyno developed and track proven</li><li>Made in the U.S.A.</li><li>Feuling® recommends pumping up each lifter by hand prior to installation, to remove all air and provide a fully pumped up lifter. Use of a thin weight oil like ATF in a squirt can works well.</li><li>Feuling® recommends Race Series® lifters for engines running higher than 185 lb (84 kg) valve spring seat pressure.</li><li>Feuling® recommends the use of a high volume oil pump which will result in quieter, better performing lifters.</li></ul>